Latest Projects Based on Solidworks

A fuel injector is a device which gives feed for the combustion chamber for the continuously timed combustion. The fuel injector also helps to get the atomization of fuel for the proper combustion, now atomization is nothing but breaking down the liquid state of fuel to very small droplets which helps to get the proper and optimized combustion. Timing of fuel injector is also an important parameter which helps the ic engine to time the process properly hence the RPM at which engine will be running is very high hence the timing of fuel spray inside the chamber is very crucial which again will be in microseconds. Hence the fuel injector should be enough accurate and controllable to work syncing with the other running parts of the engine.

This project focuses on the design and thermal analysis of rectangular fin array with perforation and without perforation. Fins are commonly used to increase

Vertical Turbine Pumps are the centrifugal pumps which are mounted vertically. Generally, turbine pumps have constant head and fluid flows uniformly at high pressure. Natural frequencies of a vertical turbine pump are

The strength assessment of the hood assembly is important when it comes to meet the design standards. The hood assembly is an important system in a car from the safety point of view and has a direct relationship with the appearance aspect of the car.

The VELOCITY-XL aircraft is a long-range aircraft with the latest technology in aerodynamics and structure to provide good maneuverability facilities and stealth mode. This can move 1100-miles cross country trips at speeds above 190 MPH while carrying four adults and baggage in total comfort. These airplanes perform best at altitudes of 8,000-11,000 feet. Landing requires a speed of about 85 MPH and a 1,500 feet long landing strip.

Fiber-reinforced polymer composite is the preferred material for the construction of aircraft and spacecraft. Even used as structural materials for the development of fuselage and due to its applications in the various field, it is used as a primary source for designing aircraft.

Aircraft safety is improving by analyzing the defects in the fuselage and catastrophic failure investigations on aircraft structural components. The primary cause of failure identification and the analysis enable recommendations for corrective action.

Why does science and technology advance so much? Why is it that we put so much effort and money into thinking about, experimenting with, and establishing new theories and principles? The primary reason for the advancements made in science is because, at the end of the day, these advancements help us lead a more comfortable life. Innovation is what led humanity to the top of the food chart, and it is what helps us stay there.

Sorting is a technique used to group similar things together. It finds extensive scale applications in mass-production facilities because, in such production facilities, similar items need to be shipped together.

Technological advancement has proved the impossible things as possible. Similarly, the recent innovations in UAV’s (Unmanned Aerial Vehicles) which are commonly known as drones paved the way for the newer way of transportation not only for carrying goods but also to carry humans from one place to another.

Increased usage of Automobiles like cars, bikes in the metro cities escalated the traffic and also increased pollution. To overcome both the issues here we are going to develop a drone project which can able to carry passengers from one place to another like a taxi.

Solidworks is a CAD (Computer-Aided Design) and CAE (Computer-Aided Engineering) software used to perform solid modelling. In this article, you will be introduced to various concepts such as part design, mechanism design, sheet metal and surface modelling.

Introduction:

The flywheel is a rotating mechanical device which is used to store rotational kinetic energy. They have a significant moment of inertia which resists change in rotational speed. In flywheel, as there is no conversion of energy from one form to another the efficiency of this tool is very high. Flywheels can also be named as mechanical batteries. The kinetic energy recovery system recovers the kinetic energy of a vehicle under braking or halting and stores this energy to be utilised when the vehicle is under movement. The loss of energy during braking is very high and the energy required during the start of the vehicle is less. Usually, during barking, the energy is lost in the form of heat or by producing some noise but when a flywheel is this energy can be reused by supplying this energy to the vehicle when it is started.

Introduction

Electricity is very important in our daily lives, we need it for various purposes. India is one of the largest producers and consumers of electricity. The demand for electricity is increasing. There is a need to produce electricity in a sustainable manner. The electricity should be renewable and efficient. About 70% of the electricity in our country is generated by thermal power plants. It is also important to produce electricity that is pollution-free and meets our daily demands. Electricity generator tiles could be a good source for producing electricity.

An executive segment is a mechanical framework that is associating the executive wheel to the system of the front wheels of a car. Pneumatic machinery consists of equipment and workings which use air power to do work. The air is controlled by control valves and dispersed through the cylinders. The notorious fame of pneumatic machinery is because of a very huge sum of power that can be transferred all the way through small tubes and flexible channels. Here, we will see how the pneumatic power steering system works using Solidworks. 

INTRODUCTION: 

It portrays a double side shaper machine utilizing a scotch burden system. A Shaper is a machine that is used for forming (metal evacuation) procedures on the workpiece. These days, Industries attempt to accomplish a high creation rate at a negligible measure of time, cost, and so on. The use of a double-side shaper machine wipes out most hindrances looked by a solitary side shaper. The fundamental position of a double-side shaper is that it diminishes time as well as creation cost. In this manner, it expands profitability. A Shaper is a kind of machine apparatus that utilizes direct relative movement between the workpiece and a solitary point cutting device to machine a direct device way. Its slice is comparable to that of a machine. This experiment can be easily carried out in Solidworks.

Latest Projects based on solidworks